Difference between revisions of "RGB-Pi JAMMA Installation"

From RGB-Pi Wiki
Jump to: navigation, search
 
(41 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
Available in English and Spanish / *Disponible en Ingles y Español*
+
<languages/>
 +
<translate>
 +
<!--T:1-->
 +
'''VideoTutorial'''
  
−
[[File:Key.png|400px|thumb|DON'T SKIP THIS STEP, put on H7 and press hard]]
+
<!--T:2-->
 +
[[Image:Tumb_j_en.png|link=https://youtu.be/GT4nnSGFv1o]]
  
−
'''JAMMA RGB-Pi Pinout'''
 
  
−
     JAMMA / MVS
+
 
 +
<!--T:3-->
 +
'''Steps by strep'''
 +
 
 +
<!--T:4-->
 +
{|
 +
|-
 +
|1. '''DO NOT SKIP THIS STEP'''. Insert the ┳ piece in pin 7 of the female JAMMA harness
 +
[[File:T.png|320px|border]][[File:Tjamma.png|320px|border]]
 +
|-
 +
|2. With the RGB-Pi board still '''DISCONNECTED''', turn on the cabinet and adjust the voltage in pin 3 to 5.25v.
 +
[[File:tester.png|320px|border]]
 +
|-
 +
|3. '''Check if your machine has a coin counter or electronic purse''' this '''can damage the rgb-pi board''', to be safe '''put a diode 1N4007''' on the pin 16 and T if you have two coin purses.
 +
[[File:Diodo.png|320px|border]]
 +
|-
 +
|4. Connect the RGB-Pi board to the Raspberry with the JAMMA connector facing to the outside of the Raspberry Pi
 +
[[File:jamma0.png|320px|border]][[File:jamma1.png|320px|border]]
 +
|-
 +
|5. If you are going to use a high volume level, you must add a heatsink like the used for the CPU of the Pi in the golden square indicated with the heat symbol, if your volume level is low and you do not notice heating in this square or you are using it [https://www.thingiverse.com/thing:5559596 a cooling system with fan ]does not need to be used.
 +
[[File:Fan1.png|320px|border]]
 +
|-
 +
|6. '''WITH THE MACHINE OFF''' connect the JAMMA RGB-Pi to the arcade cabinet. '''DO NOT PLUG ANY USB POWER ADAPTER TO THE RASPBERRY PI'''
 +
[[File:Fan2.png|320px|border]]
 +
|-
 +
|7. That's all! For instructions on how to install RGB-Pi OS, please visit the corresponding section in [[Special:MyLanguage/OS_Installation|this wiki]].
 +
|}
 +
 
 +
<!--T:5-->
 +
'''JAMMA RGB-Pi Pinout Serie4'''
 +
 
 +
     <!--T:6-->
 +
JAMMA / MVS
 
     ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
 
     ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
 
     ┃GND            A┃1            GND┃
 
     ┃GND            A┃1            GND┃
Line 13: Line 48:
 
     ┃                E┃5                ┃
 
     ┃                E┃5                ┃
 
     ┃+12v            F┃6            +12v┃
 
     ┃+12v            F┃6            +12v┃
−
     ┃Key            H┃7             Key┃
+
     ┃T PIECE HERE    H┃7   T PIECE HERE┃
 
     ┃                J┃8                ┃
 
     ┃                J┃8                ┃
 
     ┃                K┃9                ┃
 
     ┃                K┃9                ┃
 
     ┃Speaker - or L  L┃10 Speaker + or R┃
 
     ┃Speaker - or L  L┃10 Speaker + or R┃
−
     ┃P1 Button7      M┃11              ┃
+
     ┃                M┃11              ┃
−
     ┃Video GREEN    N┃12       VideoRED┃
+
     ┃GREEN          N┃12           RED┃
−
     ┃Video SYNC      P┃13     VideoBLUE┃
+
     ┃SYNC/GUN RCA    P┃13           BLUE┃
−
     ┃P2 Button 7    R┃14       VideoGND┃
+
     ┃P2 Button 7    R┃14       GUN GND┃
−
     ┃P2 Button 8    S┃15    Button8 P1┃
+
     ┃                S┃15    Button7 P1┃
 
     ┃P2 Coin        T┃16        Coin P1┃
 
     ┃P2 Coin        T┃16        Coin P1┃
 
     ┃P2 Start        U┃17      Start P1┃
 
     ┃P2 Start        U┃17      Start P1┃
Line 36: Line 71:
 
     ┃GND            f┃28            GND┃
 
     ┃GND            f┃28            GND┃
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
−
     *Pins 10 & L changes depend the switch for stereo or mono output, mono use + - indications and stereo use R & L and common ground.
+
     *Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and common ground.
−
     *Pins 27 & e are plugged to GND by defaut to enable the sixth button cut the jumpers JP1 & JP2 on the board.
+
     *Pins 27 & e are connected to GND by default. To enable the same as the 6th button on jamma, cut the jumpers JP1 & JP2 on the board.
−
    *Los pines 10 y L cambian dependiendo de la posición del switch si está en mono o estéreo, para mono usar las indicaciones + - y para estéreo R y L y una masa común.
 
−
    *Los pines 27 y e están conectados a masa por defecto, para habilitarlos como botón sexto bot'on corte los jumpers JP1 y JP2 en la placa.
 
  
−
     Kick
+
     <!--T:7-->
 +
Kick
 
     ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
 
     ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
−
     ┃P2 Button5   P2B5┃P1B5  Button5 P1┃
+
    ┃P2 Button4      4┃6      Button6 P1┃
−
     ┃P2 Button6   P2B6┃P1B6  Button6 P1┃
+
     ┃P2 Button5     5┃5      Button5 P1┃
 +
     ┃P2 Button6     6┃4      Button4 P1┃
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
 
     ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
 
     *Take the ground from any pin of the harness
 
     *Take the ground from any pin of the harness
−
    *Coger la masa de cualquier otro pin del jamma.
+
</translate>
−
   
 
−
'''JAMMA RGB-Pi installation instructions'''
 
−
 
 
−
{|
 
−
|Steps:
 
−
|-
 
−
|1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the female jamma harness
 
−
|-
 
−
|2. WITHOUT THE RGB-Pi CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v
 
−
|-
 
−
|3. If you have an electronic coin purse, check that it does not send voltage through the insert coin pin, mechanical coin purse skip this step.
 
−
|-
 
−
|4. Plug the pcb into the raspberry with the jamma connector facing out
 
−
|-
 
−
|5. Put a heatsink on the golden part indicated with the heat (same model as for Pi)
 
−
|-
 
−
|6. Download the latest version of the operating system from rgb-pi.com
 
−
|-
 
−
|7. Format one 8GB or biggest microSD in Fat32
 
−
|-
 
−
|8. Download Etcher from etcher.io to record the image in the SD
 
−
|-
 
−
|9. Record the image WITHOUT DECOMPRESSING in the SD and EXTRACT WITH SAFETY
 
−
|-
 
−
|10. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE  and WITHOUT POWERING THE Pi BY THE MICRO USB
 
−
|-
 
−
|}
 
−
 
 
−
---------------------------------------------------------------------------------------------------------
 
−
 
 
−
'''JAMMA RGB-Pi instrucciones de instalación'''
 
−
 
 
−
{|
 
−
|Pasos:
 
−
|-
 
−
|1. NO SALTARSE ESTE PASO, Ponga una de las piezas ┳ en el pin 7 del conector jamma hembra
 
−
|-
 
−
|2. SIN EL RGB-Pi CONECTADO encienda la maquina y ajuste la tension en el pin 3 a 5.25v
 
−
|-
 
−
|3. Si tienes monedero electrónico compruebe que no envía voltaje por el pin del insert coin, monederos mecánicos saltarse este paso.
 
−
|-
 
−
|4. Conecte el pcb en la raspberry con el conector jamma hacia afuera
 
−
|-
 
−
|5. Poner un disipador por la parte dorada indicada con el símbolo de calor (mismo modelo que para la Pi)
 
−
|-
 
−
|6. Descargar la última versión del sistema operativo desde rgb-pi.com
 
−
|-
 
−
|7. Formatear una microSD de 8GB o superior en Fat32
 
−
|-
 
−
|8. Descargar Etcher de etcher.io para grabar la imagen en la SD
 
−
|-
 
−
|9. Grabar la imagen SIN DESCOMPRIMIR en la SD y EXTRAER CON SEGURIDAD
 
−
|-
 
−
|10. Poner la SD en la Pi y conectar la placa jamma CON LA MÁQUINA APAGADA y SIN ALIMENTAR LA Pi POR EL MICRO USB
 
−
|-
 
−
|}
 

Latest revision as of 16:06, 12 July 2023

Other languages:
English • ‎español

VideoTutorial

Tumb j en.png


Steps by strep

1. DO NOT SKIP THIS STEP. Insert the ┳ piece in pin 7 of the female JAMMA harness

T.pngTjamma.png

2. With the RGB-Pi board still DISCONNECTED, turn on the cabinet and adjust the voltage in pin 3 to 5.25v.

Tester.png

3. Check if your machine has a coin counter or electronic purse this can damage the rgb-pi board, to be safe put a diode 1N4007 on the pin 16 and T if you have two coin purses.

Diodo.png

4. Connect the RGB-Pi board to the Raspberry with the JAMMA connector facing to the outside of the Raspberry Pi

Jamma0.pngJamma1.png

5. If you are going to use a high volume level, you must add a heatsink like the used for the CPU of the Pi in the golden square indicated with the heat symbol, if your volume level is low and you do not notice heating in this square or you are using it a cooling system with fan does not need to be used.

Fan1.png

6. WITH THE MACHINE OFF connect the JAMMA RGB-Pi to the arcade cabinet. DO NOT PLUG ANY USB POWER ADAPTER TO THE RASPBERRY PI

Fan2.png

7. That's all! For instructions on how to install RGB-Pi OS, please visit the corresponding section in this wiki.

JAMMA RGB-Pi Pinout Serie4 

   JAMMA / MVS
   ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
   ┃GND             A┃1             GND┃
   ┃GND             B┃2             GND┃
   ┃+5V             C┃3             +5v┃
   ┃+5v             D┃4             +5v┃
   ┃                E┃5                ┃
   ┃+12v            F┃6            +12v┃
   ┃T PIECE HERE    H┃7    T PIECE HERE┃
   ┃                J┃8                ┃
   ┃                K┃9                ┃
   ┃Speaker - or L  L┃10 Speaker + or R┃
   ┃                M┃11               ┃
   ┃GREEN           N┃12            RED┃
   ┃SYNC/GUN RCA    P┃13           BLUE┃
   ┃P2 Button 7     R┃14        GUN GND┃
   ┃                S┃15     Button7 P1┃
   ┃P2 Coin         T┃16        Coin P1┃
   ┃P2 Start        U┃17       Start P1┃
   ┃P2 Up           V┃18          Up P1┃
   ┃P2 Down         W┃19        Down P1┃
   ┃P2 Left         X┃20        Left P1┃
   ┃P2 Right        Y┃21       Right P1┃
   ┃P2 Button1      Z┃22     Button1 P1┃
   ┃P2 Button2      a┃23     Button2 P1┃
   ┃P2 Button3      b┃24     Button3 P1┃
   ┃P2 Button4      c┃25     Button4 P1┃
   ┃P2 Button5      d┃26     Button5 P1┃
   ┃GND/P2 Button6  e┃27 Button6 P1/GND┃
   ┃GND             f┃28            GND┃
   ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
   *Pins 10 & L change depending on the position of the stereo/mono switch. For mono use + - and for stereo use R & L and common ground.
   *Pins 27 & e are connected to GND by default. To enable the same as the 6th button on jamma, cut the jumpers JP1 & JP2 on the board.

   Kick
   ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓
   ┃P2 Button4      4┃6      Button6 P1┃
   ┃P2 Button5      5┃5      Button5 P1┃
   ┃P2 Button6      6┃4      Button4 P1┃
   ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛
   *Take the ground from any pin of the harness
Retrieved from "https://www.mortaca.com/rgb-pi/wiki/index.php?title=RGB-Pi_JAMMA_Installation&oldid=41293"