Difference between revisions of "RGB-Pi JAMMA Installation"
m (RTomas moved page Instrucciones de instalación Jamma to RGB-Pi JAMMA Installation: title change) |
m |
||
| Line 1: | Line 1: | ||
| − | |||
| − | |||
[[File:Key.png|400px|thumb|DON'T SKIP THIS STEP, put on 7 and press hard]] | [[File:Key.png|400px|thumb|DON'T SKIP THIS STEP, put on 7 and press hard]] | ||
| Line 50: | Line 48: | ||
*Coger la masa de cualquier otro pin del jamma. | *Coger la masa de cualquier otro pin del jamma. | ||
| − | ''' | + | '''Installation steps''' |
{| | {| | ||
| − | |||
|- | |- | ||
|1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the female jamma harness | |1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the female jamma harness | ||
| Line 74: | Line 71: | ||
|- | |- | ||
|10. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE and WITHOUT POWERING THE Pi BY THE MICRO USB | |10. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE and WITHOUT POWERING THE Pi BY THE MICRO USB | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
|- | |- | ||
|} | |} | ||
Revision as of 20:09, 26 April 2020
JAMMA RGB-Pi Pinout Serie4
JAMMA / MVS ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ ┃GND A┃1 GND┃ ┃GND B┃2 GND┃ ┃+5V C┃3 +5v┃ ┃+5v D┃4 +5v┃ ┃ E┃5 ┃ ┃+12v F┃6 +12v┃ ┃Key H┃7 Key┃ ┃ J┃8 ┃ ┃ K┃9 ┃ ┃Speaker - or L L┃10 Speaker + or R┃ ┃P1 Button7 M┃11 ┃ ┃Video GREEN N┃12 VideoRED┃ ┃Video SYNC P┃13 VideoBLUE┃ ┃P2 Button 7 R┃14 VideoGND┃ ┃ S┃15 Button7 P1┃ ┃P2 Coin T┃16 Coin P1┃ ┃P2 Start U┃17 Start P1┃ ┃P2 Up V┃18 Up P1┃ ┃P2 Down W┃19 Down P1┃ ┃P2 Left X┃20 Left P1┃ ┃P2 Right Y┃21 Right P1┃ ┃P2 Button1 Z┃22 Button1 P1┃ ┃P2 Button2 a┃23 Button2 P1┃ ┃P2 Button3 b┃24 Button3 P1┃ ┃P2 Button4 c┃25 Button4 P1┃ ┃P2 Button5 d┃26 Button5 P1┃ ┃GND/P2 Button6 e┃27 Button6 P1/GND┃ ┃GND f┃28 GND┃ ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ *Pins 10 & L changes depend the switch for stereo or mono output, mono use + - indications and stereo use R & L and common ground. *Pins 27 & e are plugged to GND by defaut to enable the sixth button cut the jumpers JP1 & JP2 on the board. *Los pines 10 y L cambian dependiendo de la posición del switch si está en mono o estéreo, para mono usar las indicaciones + - y para estéreo R y L y una masa común. *Los pines 27 y e están conectados a masa por defecto, para habilitarlos como botón sexto bot'on corte los jumpers JP1 y JP2 en la placa.
Kick ┏━━━━━━━━━━━━━━━━━┳━━━━━━━━━━━━━━━━━┓ ┃P2 Button4 4┃6 Button6 P1┃ ┃P2 Button5 5┃5 Button5 P1┃ ┃P2 Button6 6┃4 Button4 P1┃ ┗━━━━━━━━━━━━━━━━━┻━━━━━━━━━━━━━━━━━┛ *Take the ground from any pin of the harness *Coger la masa de cualquier otro pin del jamma.
Installation steps
| 1. DON'T SKIP THIS STEP, Put one of the ┳ pieces in pin 7 of the female jamma harness |
| 2. WITHOUT THE RGB-Pi CONNECTED turn on the machine and adjust the voltage in pin 3 to 5.25v |
| 3. If you have an electronic coin purse, check that it does not send voltage through the pin 16 or T, mechanical coin purse skip this step. |
| 4. Plug the RGB-Pi into the raspberry with the jamma connector facing out |
| 5. Put a heatsink on the golden part indicated with the heat (same model as for Pi) |
| 6. Download the latest version of the operating system from rgb-pi.com |
| 7. Format one 8GB or biggest microSD in Fat32 |
| 8. Download Etcher from etcher.io to record the image in the SD |
| 9. Record the image WITHOUT DECOMPRESSING in the SD and EXTRACT WITH SAFETY from PC |
| 10. Put the SD in the Pi and connect the jamma plate WITH THE MACHINE and WITHOUT POWERING THE Pi BY THE MICRO USB |
